login   |    register
Eduard [ MORE REVIEWS ] [ WEB SITE ] [ NEW STORIES ]

In-Box Review
135
M-36 Jackson interior for AFV Club 35058 kit

by: Bob Kerr [ HOLLOWPOINT ]


Originally published on:
Armorama

introduction
The AFV Club M-36 kit includes the basics of an interior, but much of it is left over from the earlier M-10 and Achilles kits. The Eduard photo-etch set attempts to correct some of the parts and enhance many other details. The lit includes two metal frets and a glossy rendition of the driver’s control panel to be sandwiched between the kit panel and a PE face.

the set
The first step in the set’s instructions have you cutting and sanding to remove the ammo racks from the sponson floors and replacing them with PE parts. The instructions would have the new parts placed exactly where the old ones came out. This cannot be correct because the 90mm ammo used in the M-36 was considerably larger and longer than the 3-inch ammo used in the M-10 or even the 17-pounder ammo used in the Achilles. I could not find a good shot of the sponson racks in any of my references, but I suspect that getting a set of 90mm ammo in tubes will provide the proper spacing for the racks. The PE set also includes some nice straps and other parts to dress up the ammo stowage.

Some strange hooks are provided for attaching canteens to the side of the hull interior. If these are used, they will not look right. Better to use the tie-downs (parts 56) and omit the hooks (parts 58), simply attaching the canteens over the tie-downs. On the real thing, wire hooks on the backs of the canteen’s canvas carrier attached to a loop on the hull wall.

The next step is detailing the driver and co-driver seats with parts that include seatbelts – a detail often ignored in interior detail sets.

The second page of the instructions details the driver’s control panel and the kit radio (which is not an SCR 610 as should be found in this vehicle). Other PE details in the front include interior periscope details, extra periscope stowage for the top of the transmission, the first of three fire extinguisher brackets and a detail for the turret traverse wheel.

Page 3 of the instructions is devoted to adding detail to the partial turret basket of the M-36. It also includes some parts for the gun breech and clips to hold rounds in the ready-rack at the rear of the turret. These clips (parts 64) are tiny, but nicely shaped. The kit provides about 20 of them, but you’ll only need 11 of them.

The final page of the instructions covers the rest of the interior bits for the turret. Everything is pretty straight-forward, but note that the turret side parts are shown upside-down and all the parts are subsequently installed upside down. It helps to have reference here, or you may get confused.

This is more than a mere “stick on” PE set. You will need to cut several parts, remove small detail from many parts, and grind or drill a few holes. Also, use photo references to determine the correct placement of interior accessories.



in conclusion
I’ll categorize this PE set as “moderate” in both complexity and level of detail. After adding all that detail to the inside of the M-36, it pays to also use the Eduard M-36 Jackson exterior set. I would have rated this kit higher if Eduard had offered dimensions for placing the sponson ammo racks. Recommended, with references.

My Thanks to Eduard for the review sample.



References
:“SHERMAN: A History of the American Medium Tank,” R.P.Hunnicutt., Presidio Books
“U.S. Tank Destroyers in Combat 1941-1945,” Steven J. Zaloga, Concord Publications

“U.S. Tank Destroyers of World War Two,” Steven J. Zaloga, Tanks Illustrated No. 19

“U.S. Tank Destroyers in Action,” Squadron Signal Publications
SUMMARY
While the AFV Club M-36 “Jackson” kit provides a good base for building this powerful U.S. WWII panzer destroyer, the open-topped vehicle can use some improvement. Eduard comes to the rescue with this photo-etch set to detail the interior of the kit.
Percentage Rating
60%
  Scale: 1:35
  Mfg. ID: 35883
  Suggested Retail: $24.95
  Related Link: 
  PUBLISHED: Jul 17, 2006
  NATIONALITY: United States
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 80.83%
  MAKER/PUBLISHER: 88.39%

Our Thanks to Eduard!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Bob Kerr (Hollowpoint)
FROM: KANSAS, UNITED STATES

My first memories of models is when I was a young kid living in Frankfurt, Germany, where my father was stationed with the U.S. Army. We built lots of little kits -- 1/72nd airplanes, spacecraft, cars -- it was something fun and easy to do. I continued modeling mostly cars until I was in my mid-teen...

Copyright ©2018 text by Bob Kerr [ HOLLOWPOINT ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

We broke our quick reply box. Working on it. Until fixed go to topic to reply.
Thanks.
   

What's Your Opinion?


Photos
Click image to enlarge
  • 01
  • 02
  • 03
  • 04
  • 05
  • 06