KITTY HAWK [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
UH-1D
UH-1D
  • move

by: Adie Roberts [ IN_WAR_AND_PEACE ]

History

The Bell UH-1 Iroquois military helicopter, first introduced in 1959, is the first production member of the prolific Huey family of helicopters and was itself developed in over twenty variants. The earlier "short-body" Hueys were a success, especially in the gunship role, but lacked the cabin space to be an effective troop transport. The US Army wanted a version that could carry a crew of four (two pilots and two door gunners) and also deliver an infantry section of eight-ten soldiers. Bell's solution was to stretch the UH-1B fuselage by 41 inches (105 cm) and use the extra space to fit two sideways-facing seats on either side of the transmission. This brought the total seating capacity to 15, including crew seats.
The new Huey was designated UH-1D by the US Army and as the Model 205 by Bell. The enlarged cabin could also accommodate six stretchers, double that of the earlier models, making the "Delta" a good MEDEVAC aircraft. In place of the earlier model's sliding side doors with a single window, larger doors were fitted which had two windows, plus a small "hinged panel" with an optional window, providing access to the cabin. The doors and hinged panels were quickly removable and the Huey could be flown in that configuration.
The first Army unit deliveries of the "Delta" model were on 9 August 1963 when the 11th Air Assault Division (Test) at Fort Benning Georgia received two. This unit was renamed the 1st Cavalry Division and deployed to Vietnam with its "Delta" Hueys.
A total of 2,008 UH-1Ds were delivered to the US Army between 1962 and 1966. The model was widely exported and served with the armed forces of Australia and South Vietnam among others. A grand total of 2,561 UH-1Ds were built, including 352 constructed by Dornier for the West German armed forces.

Contents

The very first thing that I noticed was the artwork “incredible” I wished they had included a picture of the artwork as it would certainly be adorning my man cave wall right now.
The box is of the usual cardboard construction with a thinner lid but solid bottom the sides of the box contain the different markings that were available with the kit.
Inside you have three sealed bags containing the plastic for the helicopter these are light beige.
Reusable sealed bag with two decal sheets one very much smaller than the other and a good sized Photo-Etch sheet.
A very nice comprehensive instruction book with some incredible pullout colour profiles of the different markings and options available. This way of displaying the colour profiles should be a standard way for all companies to show the colours and markings as they should be. This also looks very impressive as it is there for all to see just where the decals should be placed, what colours to use.
Finally a small cardboard box which contains the
Review

There really is a wow facture on opening the box so much detail, crisp manufacturing, excellent looking sprues, so let us take a closer look to see just what it really is like.
I picked the first sprue, so much detail just jumped out at me, the pilot and co-pilot seats, the canvas on the seat is stretched and looks real with the creases where they have been well worn. This is then added to by the armour plating shields and put onto the back plate then placed on the open cockpit floor. The floor itself looks very realistic with various holding points and channelling with recessed lines.
The build itself starts with the flooring and the control sticks for the Huey various control surfaces including the centre consul are just full of detail, looking at the centre consul under magnification really brings out the detail, looking again at a picture of a real consul for sure there is some minor detail missing but what is there, is enough for the scale size and really well presented. The detail for the for the internal seats really shows on the plastic the wear looking like stretched canvas all being again are very pleasing to the eye. However, the injector pin marks on the back of the seat are quite large and will need some work to correct.
The main dashboard detail is made up of raised instruments all of which look really clear and with some detailing can really make this Huey’s office look fantastic, most of the detail in the entire interior looks as you would expect. It can be made just that little bit better by either some minor scratch building with some wiring and or by the aftermarket detail that always becomes available for these kits after there initial release.
The quilted soundproofing looks really authentic and really adds to the overall feel in the Huey interior, some other parts that caught my eye were the rotary parts to the engine the detail for these are very well done. Only some of it will be visible from the top and even then will be quite covered by the blades nevertheless well represented.
The fuselage of the helicopter externally carries some great detail including rivets some panelling all look to be about right compared to photos of a real Huey. The whole kit looks to be very well thought out with little being left out more engine details are included this is another great looking part that I believe you can have exposed by removing a side panel. There are a lot of very fine small parts that you will have to cut off the sprue with some care to avoid any damage.
The tail parts of the fuselage like the main body have so much to look at with panels rivet detail it really is quite eye-catching. Weapons included are two different types of rocket pods, miniguns, 50 cal and also M60 door guns. I am very surprised by the level of detail in the door guns, in particular, adding further realism with the photo-etch parts that are included with this Kittyhawk kit.
The rotor blades look to be at the right thickness for the scale and I really like the way that Kittyhawk have gone about the realistic connections for the fitting and the weighted connecting edges.
The skids look as they should and the cross member tubes are both on the A sprue and both called A 26, however they are front and rear fitting and there is no mistake when it comes to placing these parts as it becomes obvious which one is which by the fitting connections.
The parts count for this kit is quite amazing when looking at the alternatives for the same helicopter in the same scale. The clear parts I love the way that kittyhawk place most of the clear parts into cardboard boxes thus keeping them in pristine condition during transportation. Talking of pristine I am so impressed with the amount of detail around the main piece of glazing showing rivet detail and some internal control surfaces.
All the glazing is crisp and does not appear to distort when looking through them.

The instruction booklet is very good looking wise but I have noticed one or two mistakes nothing too bad, it comes as 24 pages but these do include the colour profile pullouts. The instructions are very clear and easy to follow.
Options for the following helicopters.
UH-1D, 121st AHC.
UH-1D, 117th AHC.
UH-1D, 174th AHC.
UH-1D, 170th AHC.
German Air Force Bell UH-1D (HTG 64 Ahlhorn.
Tai Wan Air Force UH-1H.
Japanese Army, UH-1H
Conclusion

I am no expert on this particular helicopter and one of the things I have come to learn when it comes to models and modelling there is always someone who will find fault in something to do with this kit. I do feel that KittyHawk have really put some thought into this kit and have raised the boundary level with the number of parts and detail that is included in this kit.
I have become a fan of KittyHawk over the last year or so with them producing some fine kits which have been full of detail and starting to become one of the mainstream manufacturers. This kit is one of the best 1/48th scale helicopters I have seen in a long time and is also one of a very popular subject. I can only hope that in the near future they will bring out this kit in 1/35th scale as the detail and diorama options would be enormous. I am looking forward to building this kit and will hopefully be able to show you just how it all goes together.

SUMMARY
Highs: The amount of detail that Kitty Hawk has put into this kit is phenomenal
Lows: One or two mistakes in the instruction booklet make it a bit of a challenge
Verdict: I really like it the looks the detail the parts count and the subject matter make it a must for me would I recommend this kit to you? Resounding yes
Percentage Rating
90%
  Scale: 1:48
  Mfg. ID: KH80154
  Related Link: 
  PUBLISHED: Dec 06, 2017
  NATIONALITY: United States
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 88.70%
  MAKER/PUBLISHER: 86.52%

Our Thanks to Kitty Hawk!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
About Adie Roberts (In_War_and_Peace)
FROM: ENGLAND - SOUTH WEST, UNITED KINGDOM

I am disabled after a terrorist bomb I have in the past made models for TV and film and work with local museums making new models for display. I also take on commission builds for people

Copyright ©2021 text by Adie Roberts [ IN_WAR_AND_PEACE ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

Good review. This is a great kit. I have seen a couple builds of it and it can come out awesome. It does have a couple issues, but nothing really major. One seems to be a lack of locating pins on the part that holds the transmission under the rotor head. It should be angled slightly down in the front and this is not shown in the instructions. The lack of pins doesn't help this either. Warner's Wings is coming out with a correction set that will fix the transmission angle and a few other detail issues.
DEC 05, 2017 - 06:04 PM
Thank you for your comments it is a great kit and certainly the best one on the market in 1/48th scale and I for one am hoping that Kitty Hawk upscale this to 1/35th at some point. I look forward to seeing some of the aftermarket goodies coming out and will take some time to build this kit too.
DEC 05, 2017 - 06:24 PM
They are supposed to do a 1/35 version as well. Hopefully it will be soon. Here are a couple builds of it to look at for pointers: In-progress build of Vietnam era UH-1H. Aussie RAF UH-1H from Vietnam . Floyd Werner's Vietnam UH-1D. Good luck on the build and keep us posted.
DEC 05, 2017 - 07:15 PM
Thanks Arty for those build reviews I have looked through these and some very interesting comments coming from them and some positive information regarding some of the parts and the use of AM
DEC 06, 2017 - 07:07 PM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
ADVERTISEMENT